![]() ![]() ![]() If replacing your PCV valve hose is something you would rather leave to a professional, have one of YourMechanic’s certified technicians perform the replacement. Keeping your vehicle’s PCV valve hose in good working order will help the engine run cleaner and more efficiently. Reinstall any engine covers or plastic covers that were removed. Make sure to secure the hose ends with the type of clamps it is designed to use. Clamp the hose by using either the clamps provided or the old clamps. If needed, you can apply a very thin layer of grease to help slip it over the PCV valve or the intake fitting. The hose will typically slip right over the fitting when installing. Position the clamp on the PCV valve hose. Once you have identified and removed the connector, remove the PCV valve hose by gently twisting and pulling the hose away from the fitting. This requires first examining how the quick disconnect works. Quick disconnectors are removed by releasing and slightly pulling to remove. Spring hose clamps are removed by using a pair of pliers to collapse and slide the clamp away from the hose end. Gear type hose clamps are removed by using a ¼ inch or 5/16 inch socket to loosen the hose clamp and slide it from the hose ends. Your vehicle may use quick disconnectors, spring hose clamps, or gear type hose clamps. Once you locate the PCV valve, you will see how the PCV valve hose is attached to the PCV valve and the intake. It will either be retained by nuts and bolts or just snapped into place with rubber insulators. If there is a engine cover in the way of the PCV valve hose, you will need to remove it. Fits 1966 Pontiac Bonneville, 1966 Pontiac Catalina, 1966 Pontiac Grand Prix, 1966 Pontiac GTO, 1966 Pontiac. ![]() The image above shows a PCV valve (1) and the PCV valve hose (2). Connector, PCV Hose, 66 Pontiac, Tri-Power. The PCV valve is located on a valve cover, which is in various locations on the valve cover depending on the make. Part 1 of 1: Replacing the PCV valve hose A PCV valve hose failure can cause poor fuel economy, a Check Engine Light to come on, and can cause the engine to run rough. The engine reburns these gases, which reduces emissions and keeps the engine running cleaner. These gases raise emissions, so to reduce the emissions the PCV valve routes these excess gases through the PCV valve hose to the intake airbox or intake manifold. The PCV valve is activated when crankcase pressure rises in the engine when running. Always make sure to properly secure the new connector tube to prevent any leaks or loss of vacuum pressure while driving.The Positive Crankcase Ventilation (PCV) valve hose is a hose running from the valve cover on the engine to either the intake air box or the intake manifold. The job can take approximately 15-30 minutes to complete, depending on the installer's skill level and familiarity with the vehicle. It is important to note that this installation requires beginner-level skills and should be easy to complete for most individuals. Test the new connector tube to ensure proper fit and alignment.Install the new Genuine Ford PCV hose valve connector tube by aligning it with the PCV valve and the air intake hose, and securing it with clamps.Carefully remove the old connector tube from the vehicle.Use pliers to carefully remove the old connector tube from the PCV valve and the air intake hose.The connector tube is typically located on the engine, near the valve cover. Locate the PCV hose valve connector tube on your 2002-2015 Ford Ranger 3.0.Note: Before starting the installation, ensure that the vehicle is parked on a level surface. Installation Time: Approximately 15-30 minutes SKU: 97237110 Other Names: Connector Description: This GM Genuine Part is designed. It is a direct replacement for the original equipment manufacturer (OEM) part, ensuring a perfect fit and optimal performance. 97237110 - Positive Crankcase Ventilation (PCV) Hose Connector. 1399 FREE delivery Wed, May 10 on 25 of items shipped by Amazon GM Genuine Parts 12607406 Positive Crankcase Ventilation (PCV) Tube, Black 319 100+ viewed in past week 1087 17.11 FREE delivery Wed, May 10 on 25 of items shipped by Amazon More Buying Choices 9. ![]() This high-quality, new genuine Ford part is specifically designed to fit the 2002-2015 Ford Ranger 3.0 models. Are you experiencing issues with your PCV system on your 2002-2015 Ford Ranger 3.0? The Genuine OEM PCV Hose Valve Connector Tube may be the solution you need. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |